Alex Bealer Blacksmith Association of Georgia

Alex Bealer Blacksmith Association of Georgia

Search

Skip to content

Home
About Us
Events
Members
- Forum
Gallery

Search for:

Gallery

Feb 2013 Meeting - Mike LaMarre

00_demonstrator_-_mark_lamarre_5

01_twisting_vertically_in_the_vise_5

02_twisting_horizontally_in_the_vise_5

03_twisting_round_bar_with_flat_sides_5

03b_half_round_bar_twisted_5

04_flat_bar_incised_on_edge_and_twisted_5

05_flat_bar_incised_on_edge_and_face_then_twisted_5

06_saddle_to_hold_bar_stock_for_incising_5

06_spring_swage_for_incising_5

07_spring_swage_side_view_5

08_spring_swage_end_view_5

09_spring_swage_top_view_5

09b_spring_swage_stop_5

10_pineapple_twist_step_1-_incise_sides_5

11_pineapple_twist_step_2-_twist_5

12_pineapple_twist_step_3-_square_sides_5

13_pineapple_twist_step_4_-_incise_sides_5

14_pineapple_twist_step_5_-_twist_in_opposite_direction_5

14a_pineapple_twist_step_5_-_twist_in_opposite_direction_5

14b_pineapple_twist_step_5_-_continue_twisting_until_dimonds_line_up_5

15_pineapple_twist_-_tighter_twists_tightens_the_effect_5

16_cube_twist_step_1_-_incise_sides_5

17_cube_twist_step_2_-_cut_to_incised_lines_5

18_cube_twist_step_3_-_twist_5

View Slideshow

1.01__tong_half_1_first_blow_5

1.02__tong_half_1_depth_of_end_5

1.03_start_rivet_plate_5

1.04_begin_transition_from_rivet_plate_to_rein_5

1.05_contine_transition_from_rivet_plate_to_rein.jpg_5

1.06_profile_of_tong_half_to_this_point_5

1.07_draw_out_rein_5

1.08_draw_out_rein_5

1.09_smooth_rein_5

1.10_bevel_leading_edge_5

2.01__tong_half_2_first_blow_5

2.02_flare_end_5

2.02__tong_half_2_depth_and_wedge_shape_5

2.03_flare_end_5

2.04_draw_out_side_ears_5

2.05_finished_side_ears_5

2.06_forge_rivet_plate_as_before_5

2.07_begin_transition_to_rein_5

2.08_continue_transition_to_rein_5

2.09_draw_out_rein_5

2.10_clean_up_rein_5

2.11_rein_to_this_point_5

2.12_match_tong_halves_5

2.13_match_tong_halves_5

2.14_mark_for_riveting_5

2.15_rivet_5

2.16_rivet_5

2.17_size_to_the_stock_it_is_intended_to_work_with_5

2.18_size_to_the_stock_5

2.19_bend_ears_over_5

2.20_bend_ears_over_5

2.21_align_reins_over_each_other_5

2.22_finished_tong_5

2.23_finished_tong_5

Increasing the knowledge and appreciation of the Craft of Blacksmithing

Search for:

Recent Posts

Pardon our dust!

Recent Comments

Archives

September 2019

Categories

Uncategorized

Meta

Log in
Entries RSS
Comments RSS
WordPress.org

Proudly powered by WordPress